What we cover
Tile roofs installed from sub-frame preparation through ridge capping and pointing.
New tile installation
Full pitched roof tiling on new villas or completed shell structures.
Repair and replacement
Lifting cracked or slipped tiles, reseating them and stopping water ingress.
Sub-frame structure
Timber or steel battens set at the correct pitch before any tile is placed.
Underlay membrane
Breathable or bituminous underlay laid under tiles to block dust and moisture.
Ridge and edge finishing
Ridge tiles and verge pieces bedded and jointed with heat-resistant mortar.
Gutters and drainage
Gutters and downpipes fitted so rainwater discharges away from the foundations.
Signs your roof needs attention
Cracked or slipped tiles
Tiles visible from ground level that are cracked, displaced or missing expose the deck to rain and dust.
Damp patches on ceilings
Water stains on the top-floor ceiling point to tile joints or underlay that have failed and let water through.
Crumbling ridge mortar
Loose mortar fragments falling from the ridge line mean ridge tiles are no longer secure and may detach.
Fine dust falling indoors
Dust from sandstorms entering rooms through the ceiling indicates the underlay beneath the tiles has torn or lifted.
Materials and methods we use
Fired clay tiles
Withstands extreme heat, holds colour under harsh sun, and handles the daily thermal expansion cycle well.
Pressed concrete tiles
Heavier than clay, offers better thermal mass, used when the sub-frame is rated for the extra load.
Breathable underlay
Lets moisture vapour escape outward while blocking dust and water from reaching the timber deck below.
Heat-resistant bedding mortar
Used to bed ridge and verge pieces because standard mortar cracks under the severe thermal movement of Kuwait's summer.
More in general contracting.
What goes wrong on most builds.
Most problems are built in early and found late. These three cost the most to fix.
01Shortcuts under the finish
Concrete and steel disappear under the finish, so a shortcut there stays hidden until it cracks.
02Mistakes behind the wall
A water or drain mistake found after the finish means breaking new tile.
03A rushed finish
The finish is what you live with every day. Rushing it shows in every corner.
The solution?
One licensed company for the structure, the pipes and the finish.
Shortcuts under the finishEngineering supervision on site
The structure is followed before it is covered.
Mistakes behind the wallPlumbing by the same company
Laid before the walls close.
A rushed finishFinishing, and maintenance after
The same company finishes and maintains.
How it works.
First contact
Call or WhatsApp us with photos of the roof and the project location.
Site inspection
We visit to measure the roof, assess the sub-frame and confirm the tile spec.
Quote and contract
A detailed quote covering materials, labour and a work schedule is submitted.
Installation
Sub-frame prepared, underlay laid, then tiles, ridge and gutters installed in sequence.
Inspection and handover
Fixings and drainage are checked and a water test run before final handover.
What sets the price.
Pricing is set after site inspection; several project-specific factors determine the final figure.
Get a quoteRoof area
Every square metre of sloped surface is measured including all pitches.
Tile type selected
Clay, concrete and imported tiles vary widely in unit supply cost.
Sub-frame condition
Replacing or reinforcing an existing sub-frame adds material and labour cost.
Height and access
Greater height needs scaffolding or a crane lift, raising overall cost.
Gutters and extras
Gutters, downpipes and ridge vents are each priced as separate line items.
Why one contractor beats four.
Every extra contractor means another schedule and another excuse. With us, one company answers for all of it.
Turnkey
Shell and finishing with one company, from footings to keys.
Pay in instalments
Construction and finishing on instalments. Ask us for the details.
Engineering supervision
Architectural drawings and engineering supervision on site.
After handover
Maintenance contracts and a 24-hour emergency plumber.
A licensed Kuwaiti company for building construction, finishing, renovation and infrastructure works.
What our clients say.
See all reviews on GoogleExcellent
Taha Saad
Google review
Excellent
Ali Nadi
Google review
Roof-tile contractor in Kuwait. We work across all six governorates of Kuwait: Capital, Hawalli, Farwaniya, Mubarak Al-Kabeer, Ahmadi, Jahra.
Official references: Kuwait Municipality (building permits and plans)
Questions, answered.
Call nowIs roof tiling suitable for Kuwait's hot climate?
Fired clay tiles handle intense heat and daily thermal movement without degrading. The key is correct installation on a rated sub-frame with an underlay that reduces heat transfer into the building.
How often does a tiled roof need maintenance?
Inspect after each rain season and after heavy sandstorms to check mortar joints and tile seating. Periodic inspection catches small problems before they become costly repairs.
Can tiles be installed on an existing flat roof?
Yes, but a new sub-frame with the correct pitch must be built over the flat deck first. A structural check is needed to confirm the existing slab can carry the added load.
What is the practical difference between clay and concrete tiles?
Clay is lighter, absorbs heat more slowly and holds colour longer. Concrete offers better thermal mass but is heavier, so the sub-frame must be designed to handle the extra load.
Can you repair only the damaged section without retiling the whole roof?
Yes, individual cracked or displaced tiles can be lifted and replaced with matching units without disturbing the rest of the roof, provided the sub-frame and underlay elsewhere remain sound.
Licensed and registered in Kuwait.
Check us before you sign. This is our licence number and what it covers.
Find us on Google Maps